Skip to content
Spacer
Spacer

2022-2023 Applied Technology Pathway
Applied Technology guided pathway at RCC

Industrial Mechanics and Maintenance Technology Apprenticeship

Certificate of Completion

About the Program

The Industrial Mechanics and Maintenance Technology Apprenticeship certificate program is based on the Bureau of Labor and Industries (BOLI) Oregon State Apprenticeship Training Council and local Joint and Trade Apprenticeship Training Committee related training standards. It combines full-time, on-the-job work experience with trade-related theoretical instruction. This certificate is available only to BOLI-registered apprentices. If you are interested in becoming a registered apprentice in an Oregon state apprenticeship program, contact the Apprenticeship office at [email protected]. RCC supports these 8,000-hour BOLI-ATD trades: Tool and Die Maker, Millwright, and Motor Winder.

The certificate is a credential within Rogue Community College’s Industrial Mechanics and Maintenance Technology Apprenticeship Pathway. The pathway model provides statewide transfer opportunities, ladder-type certificates of completion, and an optional transfer path into a Bachelor of Science degree at the Oregon Tech. It also provides additional access to related training courses across the state for registered apprentices with aligned program outcomes, assessments and courses.

Program Learning Outcomes

The curriculum in RCC courses is derived from a set of identified learning outcomes that are relevant to the discipline. Program learning outcomes for the Industrial Mechanics and Maintenance Technology Apprenticeship Certificate of Completion are:

  • Complete a minimum of 4000 to 8000 hours State of Oregon approved on-the-job training (OJT).
  • Repair, install and maintain industrial equipment using trade specific tools and techniques in compliance with state regulations.
  • Complete a minimum of 288 to 576 State of Oregon-approved related training hours in the classroom.
  • Complete required related training with a grade C or better.

Entry Requirements

Students are required to complete the placement process to determine skill level and readiness in math, reading, and writing. As part of their training program, students must begin with the courses within their skill level as determined by placement scores.

Advanced Standing

Coursework from accredited colleges and universities will be accepted in accordance with college policies and approval of the department chair. Credits earned in the successful completion of Career Pathway Certificates can be applied to other certificates and degrees in the Career Pathway.

Graduation Requirements

Students must complete all courses in this program with a grade of “C” or better to receive their certificates. Certain required courses are graded on a pass/no pass basis only. A grade of “P” for these courses indicates a student earned the equivalent of a “C” or better grade. Students must also possess the appropriate Bureau of Labor and Industries Apprenticeship certificate and be recommended by the Joint Apprenticeship and Training Committee or the Trades Apprenticeship and Training Committee. This certificate does not guarantee licensure.

General Education Requirements

 

Course No. Course Title

Credits

BT101

Human Relations in Organizations or
PSY101 Psychology of Human Relations

3

CIS____

Approved Computer Information Science or Computer Science course, CIS120/CS120 or above, or documented computer proficiency within the past ten years 1

0-2

MTH60

Fundamentals of Algebra I or
MTH63 Applied Algebra I or higher-level math course

4

WR115

Introduction to Expository Writing or higher-level composition course

3

 

Total General Education Credits:

10-12

Millwright

 

Course No. Course Title

Credits

APR116A

Apprenticeship Millwright/Basic Electricity

4

APR116B

Apprenticeship Millwright/Carpentry

2

APR116C

Apprenticeship Millwright/Power Transmission

2

APR116D

Apprenticeship Millwright/Boilers

4

APR116E

Apprenticeship Millwright/Welding I

2

APR116F

Apprenticeship Millwright/Welding II

2

APR216A

Apprenticeship Millwright:/Machine Shop I

2

APR216B

Apprenticeship Millwright:/Machine Shop II

2

APR216C

Apprenticeship Millwright:/Drafting

4

APR216D

Apprenticeship Millwright: Hydraulics and Pneumatics I

2

APR216E

Apprenticeship Millwright: Hydraulics and Pneumatics II

2

APR216F

Apprenticeship Millwright: Rigging

4

 

Total Millwright Credits

32

MINIMUM TOTAL PROGRAM CREDITS REQUIRED:
42-44

1 Required for graduation.


For more information, contact the Apprenticeship Office.

Apprenticeship faculty and staff can also be reached by:
Phone: 541-956-7500
Email: [email protected]
Web address: www.roguecc.edu/apprenticeship
TTY: Oregon Telecom Relay Service, 711