Industrial Mechanics and Maintenance Technology Apprenticeship
Certificate of Completion
About the Program
The Industrial Mechanics and Maintenance Technology Apprenticeship certificate program is based on the Bureau of Labor and Industries (BOLI) Oregon State Apprenticeship Training Council and local Joint and Trade Apprenticeship Training Committee related training standards. It combines full-time, on-the-job work experience with trade-related theoretical instruction. This certificate is available only to BOLI-registered apprentices. If you are interested in becoming a registered apprentice in an Oregon state apprenticeship program, contact the Apprenticeship office at [email protected]
The certificate is a credential within Rogue Community College’s Industrial Mechanics and Maintenance Technology Apprenticeship Pathway. The pathway model provides statewide transfer opportunities, ladder-type certificates of completion, and an optional transfer path into a bachelor of science degree at the Oregon Tech. It also provides additional access to related training courses across the state for registered apprentices with aligned program outcomes, assessments and courses.
Program Learning Outcomes
The curriculum in RCC courses is derived from a set of identified learning outcomes that are relevant to the discipline. Program learning outcomes for the Industrial Mechanics and Maintenance Technology Apprenticeship Certificate are:
Complete a minimum of 8,000 hours State of Oregon approved on-the job training (OJT).
Repair, install and maintain a variety of industrial equipment using trade specific tools and techniques in compliance with state regulations.
Seventy-five percent of applicants have documented trade-specific skills listed on the Industrial Mechanics and Maintenance Technology Apprenticeship Trades Outcomes Assessment Tool.
Complete required related training with a grade C or better.
Entry Requirements
Students are required to take a placement test to determine skill level and readiness in math, reading and writing. As part of their training program, students must begin with the courses within their skill level as determined by placement scores. In addition, students may also be required to enroll in classes that would increase their employability and success.
Advanced Standing
Coursework from accredited colleges and universities will be accepted in accordance with college policies and approval of the department chair. Credits earned in the successful completion of Career Pathways certificates can be applied to other certificates and degrees in the Career Pathway.
Graduation Requirements
Students must complete all courses in this program with a grade of “C” or better to receive their certificates. Certain required courses are graded on a pass/no pass basis only. A grade of “P” for these courses indicates a student earned the equivalent of a “C” or better grade. Students must also possess the appropriate Bureau of Labor and Industries Apprenticeship certificate and be recommended by the Joint Apprenticeship and Training Committee or the Trades Apprenticeship and Training Committee. This certificate does not guarantee licensure.
MINIMUM TOTAL PROGRAM CREDITS REQUIRED: |
42-44 |
Program Map
General Education Requirements |
|
|
Course No. | Course Title | Credits |
---|---|---|
BT101 |
Human Relations in Organizations or | 3 |
CIS/CS |
Approved Computer Information Science or Computer | 0-2 |
MTH60 |
Fundamentals of Algebra I or | 4 |
WR115 |
Introduction to Expository Writing or higher level composition | 3 |
|
Total General Education Credits: | 10-12 |
Millwright |
|
|
Course No. | Course Title | Credits |
APR116A |
Apprenticeship Millwright/Basic Electricity | 4 |
APR116B |
Apprenticeship Millwright/Carpentry | 2 |
APR116C |
Apprenticeship Millwright/Power Transmission | 2 |
APR116D |
Apprenticeship Millwright/Boilers | 4 |
APR116E |
Apprenticeship Millwright/Welding I | 2 |
APR116F |
Apprenticeship Millwright/Welding II | 2 |
APR216A |
Apprenticeship Millwright:/Machine Shop I | 2 |
APR216B |
Apprenticeship Millwright:/Machine Shop II | 2 |
APR216C |
Apprenticeship Millwright:/Drafting | 4 |
APR216D |
Apprenticeship Millwright: Hydraulics and Pneumatics I | 2 |
APR216E |
Apprenticeship Millwright: Hydraulics and Pneumatics II | 2 |
APR216F |
Apprenticeship Millwright: Rigging |
4 |
|
Total Millwright Credits |
32 |
1 Required for graduation.
For more information, contact the Apprenticeship Office.
Apprenticeship faculty and staff can also be reached by:
Phone: 541-956-7500
Email: [email protected]
Web address: www.roguecc.edu/apprenticeship
TTY: Oregon Telecom Relay Service, 711